恒溫水浴振蕩器具有結構合理、操作簡便、穩定性能高等特點，是實驗室工作人員得心應手的理想設備。

恒溫水浴振蕩器常見故障及處理

1、故障現象：恒溫水浴振蕩器加熱正常，振蕩無法工作。

解決方法：① 打開控制柜側板，接通電源，將溫控設定為0度（即不加熱狀態），打開振蕩開關，將速度調至最高；② 用萬用表（交流250檔）測量變壓器有無220V電壓輸入，若無則開關壞，反之，測量變壓器有無12V電壓輸出（用交流50V檔），無則變壓器壞；③ 此時切勿輕易更換變壓器，該情況多為線路板中整流部分或電機出現短路故障（出現此種現象，變壓器外觀有燒焦現象），在排除以上情況，更換即可；④ 12V電壓正常，檢查有無直流12電壓（直流50V檔），沒有則整流橋斷路，更換；⑤ 有則檢查有無電壓輸出至電機（5-8V左右），有則電機壞或由于儀器長時間沒有使用，機械部分銹死，沒有則控制板中大功率管壞。

2、故障現象：加熱正常，振蕩速度變慢。

解決方法：打開控制柜側板，接通電源，將溫控設定為0度（即不加熱狀態），打開振蕩開關，將速度調至最高，找到速度控制板上的兩個可調電阻，逆時針調整右邊的即可解決。

3、故障現象：恒溫水浴振蕩器不加熱，振蕩正常。

1）顯示正常，設定正常，無法加熱。該故障解決方法：接通電源，打開電源開關，調整設定溫度高于實際測量溫度，檢查溫控儀有無輸出指示，有則測量加熱管是否有電壓輸入，有則加熱管壞，更換即可，沒有電壓輸入加熱管，多為繼電器發生故障。若溫控儀沒有電壓輸出指示，建議更換溫控儀。

2）溫控儀顯示LLL或999（根據廠家不同，參數有所不同）該故障為溫度傳感器斷路或短路，更換傳感器即可。

3）溫度不受控制繼電器壞或傳感器受潮。